MOTOBLUE™ EMISSIONS LEGAL X PIPE

Why should you upgrade your factory stainless H-pipe?

The Mustang's factory H-pipe flows well, but loses its ability to merge exhaust gases above 3000 RPM and thus becomes a non-functional part of the exhaust system. The Mustang's factory OEM cats are adequate flow cats. Rather than replace your entire stainless H-pipe with a new one, Simply upgrade it with the MOTOBLUE™ custom-made stainless X-pipe crossover.

Upgrading from the factory H-pipe to the MOTOBLUE™ stainless X-pipe will add a DYNO-proven 8 HP. This better "breathing" stainless steel X-pipe increases horsepower, torque and sound quality. Best of all, it can be added to your existing OEM-catted h-pipe by simply cutting the factory h-pipe in the appropriate spot and slipping this X-pipe over the existing pipes.

With a slip fit stainless steel band clamp connection, this is a simple slice-in/bolt-on kit, and installs in 45 minutes or less.

Note : This is a slice in X-pipe; you will be required to cut the factory h-Pipe

MOTOBLUE™ Emissions Legal X-pipe
• 2½ T-409 Stainless Steel X-Pipe
• Hangers, stainless band clamps
• Requires cutting of factory h-pipe
• Simple bolt on no welding

MOTOBLUE™ GEN II EMISSIONS LEGAL X PIPE UPGRADE KIT

Are you looking to improve the flow on your aftermarket Emissions Legal X-pipe?

If so, the engineers at MOTOBLUE™ have the answer for you. The MOTOBLUE™ Emissions X-Pipe Upgrade kit replaces your old factory OEM cats with stainless High-Flow Emissions Legal high-flow cats.

Upgrading from the factory H-pipe to the MOTOBLUE™ stainless steel High-Flow Emissions Legal high flow cats will add a DYNO-proven up to 12 HP. . This better "breathing" High-Flow Emissions Legal cat add horsepower, torque and sound quality.

Simply un-bolt the factory cat pipes and slip on a set of the MOTOBLUE™ GEN II EMISSIONS LEGAL cats and front legs. With a slip fit stainless steel band clamp connection, this kit is a simple bolt-on and installs in 45 minutes or less.

MOTOBLUE™ Emissions Legal X-pipe
• 2½ T-409 Stainless Steel Front Legs
• 2½ T-409 Stainless Steel Hi-Flow Cats
• Stainless band clamps
• Simple bolt-on, no cutting, no welding

MOTOBLUE™ Stainless 2½ Over-Axle™ Pipes

The factory Mustang GT over axle pipes are 2.5" diameter piping, but it ends there. Ford over axle pipes are creases as they travel over the axles hampering flow by as much as 5%, reducing the performance of their exhaust design.

MOTOBLUE™ has the solution with their new T-409 Stainless 2½ Over-Axle™ Pipes, featuring smooth fully mandrel bent piping allowing maximum flow of exhaust gases with increased performance and fit. Correct bending and sizing make your installation a breeze.

All MOTOBLUE™ over-axle pipes are factory-checked for proper fitting and DYNO-tested to verify performance gains. Backed by MOTOBLUE's lifetime warranty, you will be able to enjoy a rich, powerful sound--from now on!

This kit is a quick and simple bolt-on installation with basic hand tools (no welding or cutting required).

MOTOBLUE™
• T-409 Stainless Steel (bolt-on) 2½ Over-Axle™ Pipes

MOTOBLUE™
• Polished T-304 Stainless Steel (bolt-on) 2½ Over-Axle™ Pipes

MOTOBLUE™ AXLE-BACK RACE PIPES

Why bottle up your Mustang’s high-horsepower engine with restricting, docile-sounding stock mufflers? If you’re looking for the best-flowing, meanest-sounding axle-backs in the business, look no further.

Install a set a specially designed MOTOBLUE axle-back RACE pipes, and replace that traditional muffler design, allowing your Mustang to provide unmatched power increases and a wicked "wide-open" sound. This affordable, easy to install kit eliminates the factory mufflers entirely, drastically reducing back pressure for enhanced power and a mind-blowing performance sound. Nothing else even comes close! You'll both feel and hear the difference! Gains of up to 11 HP are possible, depending upon the application.

With a slip fit stainless steel band clamp connection - This kit is a simple bolt-on and installs in 45 minutes or less.

MOTOBLUE™ Axle-Back RACE Pipes
• Constructed entirely from 304 stainless steel mandrel-bent 2.5" tubing
• Hand-polished, 4.0" 304 stainless tips for a show-quality appearance
• Significantly lighter than the OEM muffler assembly, Installs in under 30 minutes
• Pre-welded hangers, detailed instructions, and all necessary installation hardware

Pypes Stainless Dual Exhaust Hardware Kit
• 304 Stainless Exhaust Hangers, band clamps
• Nuts Bolts and detailed installation instructions