Snow Performance Boost Cooler
Water/Methanol Injection Systems

Snow Performance's Boost Cooler System is an alternative, addition to traditional intercooled turbocharger, supercharged, and nitrous oxide-fed powerplants. Snows water-methanol injection controls detonation by cooling the inlet-air charge. Water basically cools the intake charge and combustion process. Methanol works as a cooling agent, but also serves as an extremely high-octane fuel. With an oxygen-heavy, denser charge and more ignition timing, horsepower gains can be impressive, thanks to the mist of this simple mixture.

Methanol Injection suppresses detonation so more power can be utilized as with any intercooled system. Water, with its high latent heat of vaporization cools the intake charge and combustion. Methanol cools the charge and combustion but also acts like an extremely high octane fuel (some researchers claim as high as 120 octane) as well as adding more oxygen to combustion.

The gasoline Stage 1 Boost Cooler™ kit is available for forced induction applications that are either fuel injected or carbureted. Operation is very simple: the system starts injecting when the boost switch reaches the user-adjustable point and it injects a fixed amount of fluid through the nozzle until the switch opens again. This makes it a good choice for low to medium boost setups looking for an octane enhancement and cooler intake charge. Activation can also be set up through any other user-chosen switch, such as a full throttle micro-switch, etc.

Optional Accessories:

Listed below on this page


• Snow Boost Juice™
  
  
• Nitro Booster™
  
  
• 7-Quart Upgrade Reservoir
  
  
• Low Level Indicator

Stage I Boost Cooler™ Kit includes:
-150+ PSI High Volume Pump, 3 Quart Reservoir
-2 Nozzles To Cover a Wide Range of Horsepower
-All Required Hardware Needed For Install, Comprehensive Instructions

Boost Juice™
• A proprietary mix of 49% methanol and 51% water.
• 4 Gallon case, *NOTE* Boost Juice CAN NOT be shipped outside of the United States. Boost Juice CAN ONLY be shipped using Ground service.

Nitro Booster™
• Up to a 30 to 50hp increase can be measured
• *NOTE* Nitro Booster CAN NOT be shipped outside of the United States.

2.5 Gallon Reservoir Tank
• Water Injection Reservoir, Plastic, 2.5 Gallon Reservoir (7 Quart)
• 13”l x 9.5”h x 7.5”w (similar to a very small car battery)
• Includes an additional 10 feet of tubing.

Low Level Indicator
• This is a float switch and indicator light that lets you know when your reservoir is running low on fluid.

This kit uses the 0 to 5 Volt output signal from the Mass Air Flow sensor on fuel injected vehicles. This means that any vehicle with a MAF (with a 0-5V output signal) can use this kit, whether they are naturally aspirated or forced induction.

If the application is forced induction, it can be used with very fast-spooling turbos, or positive displacement blowers. It is easier to set up with the positive displacement blowers with a MAF signal because it is more progressive in nature vs. the boost pressure signal (stage 2 boost cooler™ kit) on those applications. This allows for the most accurate injection possible over the widest range. The result is the most power and driveability possible. This system comes with Limited Lifetime Warranty.

This kit uses manifold boost pressure to determine when and how much fluid to inject. Proportionally injecting according to boost pressure gives the most accurate delivery of water-methanol and allows the most cooling and performance improvement over the widest range. More power and driveability is the result.

It can be used on any forced induction engine: carbureted, fuel injected, turbocharged, positive displacement or centrifugal blowers. The most suitable are the centrifugal supercharged and turbocharged engines, as they build boost is a more progressive manner concerning water-methanol injection. The positive displacement blower engines will work, but it might take more work to dial in the delivery. For higher boost applications (over 25psi), the controller can be upgraded to the snow VC100 unit. This system comes with Limited Lifetime Warranty.

Stage II Boost Cooler™ Kit includes:
-150+ PSI High Volume Pump, 3 Quart Reservoir
-Adjustable Digital Variable Controller
-2 Nozzles To Cover a Wide Range of Horsepower
-All Required Hardware Needed For Install, Comprehensive Instructions

Boost Juice™
• A proprietary mix of 49% methanol and 51% water.
• 4 Gallon case, *NOTE* Boost Juice CAN NOT be shipped outside of the United States. Boost Juice CAN ONLY be shipped using Ground service.

Nitro Booster™
• Up to a 30 to 50hp increase can be measured
• *NOTE* Nitro Booster CAN NOT be shipped outside of the United States.

2.5 Gallon Reservoir Tank
• Water Injection Reservoir, Plastic, 2.5 Gallon Reservoir (7 Quart)
• 13”l x 9.5”h x 7.5”w (similar to a very small car battery)
• Includes an additional 10 feet of tubing.

Low Level Indicator
• This is a float switch and indicator light that lets you know when your reservoir is running low on fluid.