DIABLOSPORT MAFIA MAF MASS AIR ADAPTERS | FREE SHIPPING

diablosport mafia
DIABLOSPORT MAF.ia MAF Interface Adapter
Extend the volt limits of factory MAF, no more pegging your MAF

Are the limitations of your factory MAF sensor hindering your tune? Well not anymore. Diablosport’s new MAF.ia works with the factory sensor to extend voltage limits with a multitude of settings intended for vehicles making anywhere from 400 to over 900+ horsepower, whether they be naturally aspirated or supercharged.

 

The DiabloSport MAFia provides real world plug and play control of your vehicle’s Mass Air Meter (MAF). Mafia allows you to precisely control and regulate MAF sensor voltage eliminating the need for Pre-fabricated custom MAF sensors.

The MAFia uses factory connectors and harnesses to attenuate the signal to a vehicle’s MAF, and keeps allows vehicles with stock MAF’s to run beyond the standard 5 Volts. When a vehicle normally reaches 5 volts, it “pegs the meter” or maxes out the signal, keeping the vehicle from making peak horse power at high RPM.. The MAFia attenuates this signal, and will allow a vehicle to make up to 800 RWHP without “pegging the meter”

WHAT IS THE DIABLOSPORT MAF.ia?

The DiabloSport MAF.ia. for Ford vehicles is a plug and play in-line devise that allows end-users to regulate MAF sensor voltage in forced induction and high horsepower applications eliminating the need for aftermarket MAF sensors. The MAF.ia. “tweaks” the always reliable factory MAF signal to eliminate fatal conditions caused by high MAF volts.

The MAF.ia. is a necessity for custom and dyno tuning dealers, with a wide range of applications, a few simple part numbers cover all customers’ calibration needs and at a fraction if the cost of replacement MAF sensors.

MAF.ia. eliminates the need for a calibrated Mass Air Flow meter for bigger injectors.

MAF.ia. works with the factory Ford MAF sensor to extend voltage limits Using multiple settings, for 400 to 900+ RWHP, supercharged or high Horsepower naturally aspirated Ford applications.

MAF.ia. is the less expensive, High Tech injection molded plastic, Alternative to the "BIG clumsy, like factory calibration" aftermarket MAF sensors, no clamps Or ill fitting hoses, Simply plug and play.

MAF.ia. allows the end-user to maintain the OEM quality Drivability of the factory MAF sensor output while realizing all the benefits of a recalibrated MAF sensor.

    DIABLOSPORT MAF.ia Features & Benefits

  • No need to cut your wiring harness - MAF.ia. is fully plug and play
  • Works with both 4 and 6 wire MAF sensors
  • 8 user selectable settings for different HP levels (Stock to Gangster level)
  • LED indicator of MAF voltage status
  • MAF.ia. also works as a MAF extension harness
  • High-tech case design

    DiabloSport MAFi.a. Applications

  • F7373- 1986-04 Ford Vehicles (MAF equipped)
  • F7383- 1986-04 Ford Vehicles (MAF equipped 3 extender harness for relocating MAF)
  • F7370- 2005-07 Ford Vehicles ( includes 04 F-150)
  • F7396- Factory Pigtail 1988-04 for replacing old or damages MAF connections (36”)
  • F7324- MAF converter 2005-10 to 1996-04 vehicles.

DIABLOSPORT MAF.ia MAF Interface Adapter - 24"
Ford 2005-10 Applications
  • Plugs in-between factory MAF sensor and factory MAF harness
  • Fully plug-and-play, eliminating need of cutting factory harness

  • DIABLOSPORT MAF.ia MAF Interface Adapter - 12"
    Ford 1996-04 Applications
  • Plugs in-between factory MAF sensor and factory MAF harness
  • Fully plug-and-play, eliminating need of cutting factory harness

  • DIABLOSPORT MAF.ia MAF Interface Adapter - 36"
    Ford 1996-04 Applications
  • Plugs in-between factory MAF sensor and factory MAF harness
  • Fully plug-and-play, eliminating need of cutting factory harness

  • DIABLOSPORT MAF.ia MAF REPLACEMENT Connector KIT - 36"
    Ford 1988-10 Applications
  • This connector is a factory quality pigtail for installing the 1996-2004 MAF sensors on 1988-1995 vehicles or for repairing old damaged MAF pigtails on late model Ford cars or trucks and can be used for 4 or 6 pin configurations.
  • Built in 36" length for use in MAF relocation or cut length to suit needs. Cutting and splicing to the factory wiring harness is required.